1W Wireless Pump Control Remote Pump ON OFF Control Embedded
Wireless Solution 2km
Hardware needed:
1. 12V DC Power supply
2. Floating switch (with high and low level)
3. LS-RDI00 (with antenna)
4. LS-RDO01(with antenna)
5. Pump
6. Solid state relay
Parameter:
| Parameter |
| Power output: | 600mW |
| Wireless technology: | Lora |
| Power supply: | 9V-30V (usually choose 24V DC or 12V DC) |
| Control distance: | 5km LOS |
| Baud rate: | 2400bps |
| Receiving sensibility: | -123dBm@1200bps, -118dbm(9600bps) |
| Networking |
| Networking: | Point to point and point to multipoint |
| Protocol: | Modbus RTU protocol |
| Port Description |
| Input: | 2 active inputs (passive customize), isolated |
| Output: | 2 passive relay outputs, isolated contact max load AC250V/5A,DC30V/5A (active outputs 0-5V customize) |
| Communication port | RS485 (wireless RS485 customize) |
| Current |
| Transmit current: | <350mA |
| Receiving current: | <20mA |
| General |
| Frequency: | 915MHz |
| Channel No: | 16 channels, can change via DIP switch |
| Physical Properties |
| Dimension: | 115×90×40(mm) |
| Antenna Connector: | SMA,vehicle antenna with 1.5m cable |
| Temperature: | -35℃~+75℃( industrial) |
| Mounting method: | Standard 3.5 inch industrial guild rail |
System diagram
Tank side high level or low level, Pump side ON or OFF
When water level low, pump ON. When water level high, pump OFF
How to connect tank side---LS-RDI00
How to connect pump side---RDO01
About LS-RDIO controller
2 controllers should set with the same ID
2 controllers should set at the same channel
1 controller sets as master, 1 controller sets as salve
If you use different sets in the same area, please use different ID
and channel for different sets.
Application area:
Wireless pump controls
Automate your tank level without running wire between the well pump
and the tank. Wireless pump controls save you time and money.
Wireless tank level monitoring
simple wireless monitoring of your tank level from a remote
location and receive critical status updates.
Wireless valve activation
Open or close electronic wireless valves, solenoid valves.
Smart agriculture
Pivot irrigation, soil pressure and temperature monitoring
Emergency Notification
Receive critical status updates by email, phone, cell phone, or PDA
if equipment fails
Conveyor Control
Control a conveyor motor remotely
Remote Control Relay
Use dry contact inputs to control a remote relay.
Problem Notification
Save time in large facilities by activating an overhead
notification light when a problem occurs, letting the supervisor
know exactly where to go.
Dust Suppression
Use wireless I/O module to operate your dust
Data Logging
Wirelessly acquire and log various data from a remote location
using our analog I/O module
Stacker Control
Start and stop your stacker/reclaimir. Connect PLC in control
center with stacker and reclaimer.
Proximity Detection
Mount a transmitter with adjustable range on heavy equipment, mount
a receiver in a “blind spot,” and then set up the receiver to sound
an alarm or turn on a light whenever the equipment is operating in
the area.
Chemical Level Monitoring
Monitor water chlorination or other chemicals remotely.
Traffic Signals
Avoid having to lay new wire by using wireless transmitters and
receivers to control traffic signs such as “Railroad Crossing
Ahead” when a train is present.
Grain Elevators
Our wireless transmitters and receivers can be used to monitor
grain elevator conditions or control different functions. To
collect RS485 data. To monitor temperature and humidity in Grain.
Freight Loading
Digital I/O module for crane control and analog I/O module to send
the load information wirelessly to another location.
